[Tutorial] Update ICS to Jelly Bean 4.1.2 for Flare
Complete Tutorial (Flare ICS to JB)

Do this at your own Risk (This procedure works 100% on my device)

Requirements:Win XP 32bit or Win 7 32bit and 64bit (all tools set to Win Xp Sp3 Compatibility & Run as Admin)
Required Files:

RoadKill’s Disk Image
You must post to unlock this link

Download This Complete Req.
You must post to unlock this link

StockJB v31:
You must post to unlock this link

Chapter 1: ICS BACKUP
1.1. Backup your ICS using Roadkill.
1.1.1. Turn off your Flare, then press Volume down and power button at the same time. once you see the “ENTRY QPST DOWNLOAD”, open roadkill and click on Store Image Tab, select the disk with 3.61GB, click browse and select the location where you want your backup to be saved, and click start. Once finish proceed to next step.

[Image: jl2grr.png]

Chapter 2: WRITING
2.1. Write your IMEI1, IMEI2, Wi-Fi Mac, and Serial Number (S/N) in a piece of tissue paper. XD
2.1.1. To do that, turn on your Wi-Fi, and go to Settings > About Phone > Status. If some are missing just dial *#0000# in dial pad.
2.2. Extract all the filesyou downloaded. Make sure you remember the location of the file.

3.1. Backup NVRam
3.1.1. Run EMMC_DownLoad_V1.2.3.exe ,(Check Download Boot Loader for 1st run)
3.1.2. Turn device ON (make sure USB Debugging is enable)
3.1.3. Connect phone thru microUSB cable (Note: Make sure there are no other USB Modem or phone connected to your computer except for Flare)
3.1.4 Click BackUp_NV.
3.1.5. Wait until back up is successful.

[Image: ny8zgn.png]

3.2. Download BP Firmware (“ENTRY QPST DOWNLOAD” Mode)
3.2.1. Run EMMC_DownLoad_V1.2.3.exe. Click SELPATH select “BP Firmware” Folder.
3.2.2. Connect phone thru a microUSB cable. Check Device Manager for Com Port #.
3.2.3 Look for "Qualcomm HS-Usb Diagnostics 9006" type the Comport # in EMMC Download Box. Click Download.
3.2.4. Wait until download is successful (Usually it takes 6-12sec). Remove battery. (Do not Close EMMC Download. then proceed to next Step )

[Image: 2w20x1y.png]
[Image: 301kl8z.png]
[Image: 34e4390.png]

3.3. Download AP Firmware (Fastboot Mode) or (Green Screen Mode)
3.3.1. Run QUALFAST2.0.5.exe. Click SELPATH, select AP firmware (“Stock JB Rom” Folder),Check Format Card &Userdata
3.3.2. Press Power button and Volume Up simultaneously. (Fastboot Mode) "Green Screen"
3.3.3. Click OK to start download then connect phone thru a microUSB cable.
3.3.4. Wait until download is successful. Remove battery.

[Image: 5jtxc4.png]
[Image: f1e92v.png]

3.4. Restore NVRam Backup
3.4.1. Run EMMC_DownLoad_V1.2.3.exe.
3.4.2. Turn device ON. (make sure USB Debugging is enable)
3.4.3. Click Restore_NV. Browse and select bak.qcn file. Connect phone thru microUSB cable.
3.4.4. Wait until qcn restore is successful. (your IMEI 2 is Null &Wifi Mac Address is set to default. you need to write it again)

[Image: 23tmgsy.png]

Chapter 4:IMEI 2 & Wi-Fi MAC Address Writing
4.1. IMEI 2 &Wifi Mac address Writing
4.1.1. Turn device ON (make sure USB Debugging is enable)
4.1.2. Locate your modem com port number (Go to Device Manager >Right-click “Tianyu HS-USB Android Modem 9025”> Properties > Advanced Tab > Advanced Port Settings > COM Port # (Ex. 10))
4.1.3. Open Qualcomm_Modem_Tools_V1.1.2.exe and type com port #
4.1.4. Write all your backup code, then click Write button. (In my case I have re-entered my IMEI1, IMEI2, S/N (Serial Number), Wi-Fi MAC)

Note: Every after successful entry of IMEI, the phone automatically restarts.

[Image: 2zjeuet.png]
[Image: 35jdyy9.png]

F. Restart Device. Wait until it boot perfectly

Chapter 5: Flash the BuglessFlashable via Recovery Stock JB ROM (already rooted)
5.1. You know already how to do that.

Credits to all sources..!!

Credits to Alkane, Philip, Paul Caliva, Heartles Bdeck, Reymar of S100 And Cherry Mobile.

Sana makatulong.


Sa mga nahihirapan mag install ng Tianyu Modem driver for Windows 7 64bit OS.Warning!!!
Follow at your own risk, Wag ninyo akong sisihin kung hindi magwowork sa PC niyo ito...

Tested on my Laptop with Win7 64bit and successfully updated my FLARES to Jellybean following Alkanes tutorials.Gawin niyo lang ito if hindi niyo talaga ma install ang drivers.

Reboot your computer/laptop
Press F8
May lalabas na "Choose advance options for: Windows 7
Boot or Choose "Disable driver signature enforcement"
Once na load na windows niyo
Manually Install the drivers
Video link how to manually install the drivers.
You must post to unlock this link
(Note: nasa Normal windows booting ako ng nag record nito kaya nag error nung ininstall ko)
Once na install na drivers don't reboot your PC/Laptop, proceed with the updating to Jellybean.
Enjoy your Jellybean
Thanks Quote
salamat sir Ven.meron po bang pangdowngrade into ics?sira kasi auto rotate/tilting ko.haist
Thanks Quote
pasilip nga po nito
Thanks Quote
pasilip nga po nito
Thanks Quote
try try try trytry trytry trytry trytry try
Thanks Quote
(01-26-2014 12:39 AM)anhtuan2364 Wrote:
You must post to unlock this link
try try try trytry trytry trytry trytry try

Staff Message STAFF MESSAGE:  @"anhtuan2354" Post Properly! Avoid Spamming!

Thanks Quote
maupdated nga to thanks.
Thanks Quote
thanks! maitry nga ito. Smile
Thanks Quote
4.2 Toggles Data Icon activate on 1st Installation - Fix deactivate on Settings/More/Mobile network.
Recent Clear Button when pressing HOME not working - Fix Manual Clear recent apps.
Thanks Quote
maupdated nga to thanks.
Thanks Quote

Full Site | MP3 Search | Youtube Downloader | Free SMS